Chapter 67: The Divergent Path of Steelmaking
Tomorrow afternoon features the Featured New Book Recommendations for Category Fiction and the Featured New Book Recommendations for the History Channel. Therefore, I will post two chapters today and three chapters tomorrow. Wishing for everyone's understanding.
However, I still owe everyone one chapter; I haven't forgotten. Allow me to collect my thoughts over the next couple of days, and then I'll unleash a mass release for you all!
Additionally, I am, of course, asking for votes...
*************
Fang Jun knew that the various manufacturing techniques of the Tang Dynasty were quite backward, and he also knew that the best craftsmen of this era were conscripted by the government. State-run handicrafts had always occupied a dominant position in ancient handicrafts, representing the highest level of production skill.
Craftsmen were concentrated in workshops established by the government, using raw materials supplied by the state, and under the supervision of official overseers, they manufactured and processed products designated by the government.
Their occupations were hereditary, working for the government generation after generation.
Yet, he never expected that the Fang family's blacksmith shop would be so crude.
A row of adobe houses was built along the hillside, forming a semicircle. Several shaft furnaces stood in front of the houses, presumably used for smelting iron.
The furnaces were about five or six meters high, with a base diameter of around three meters, thicker in the middle and slightly narrower at the ends, with outer walls paved with gravel. There was a charging port at the top and a blast tuyere at the bottom. In this way, a relative motion of descending furnace charge and ascending gas could be formed. The high-temperature gas generated by combustion would rise through the material layer, transferring heat to the charge, which served as the preheating process.
However, there was no blower in sight, and only some coal slag remained inside the furnace chamber.
Fang Jun had never seen what an iron smelting furnace looked like before, but that didn't stop him from understanding the principle after a single glance. One didn't need to have studied industrial manufacturing; just a little basic common sense in physics was enough to figure it out, especially since this contraption was truly crude.
Fang Jun asked Lu Cheng behind him, "Is this an iron smelting furnace? Why aren't they smelting iron?"
Even though most of the ore mined from the nearby mine tunnels was pyrite, which couldn't yield much of anything, they couldn't just leave it idle like this, could they?
Lu Cheng replied, "That's right, it's an iron smelting furnace. It's winter now, and it's too cold; the furnace temperature can't get high enough, so we aren't smelting iron."
Fang Jun smacked his lips, thinking that this lousy furnace was simply too crude. Not only could the furnace temperature not rise in the winter, but even in the hottest days of summer, how high could the temperature possibly get?
What was the required temperature for smelting iron again?
Fang Jun tugged at his hair and thought about it. Probably a little over a thousand degrees? That sounded about right. Then steelmaking would require at least upwards of fifteen hundred degrees. This wretched furnace struggled even with smelting iron, so steelmaking was completely out of the question.
If he had only studied science back in the day—iron smelting, steel smelting, cement making, and the like—he might have been able to trigger the First Industrial Revolution right at the start of the Tang Dynasty.
Oh, right, what was the hallmark of the First Industrial Revolution again?
It seemed to be the steam engine...
Now that he thought about it, the principle of the steam engine was explosively simple; the difficulty lay in the scarcity of materials and standards falling short of craftsmanship. Generally speaking, it didn't seem entirely impossible to manufacture.
Ah, his thoughts had drifted too far...
Fang Jun glanced at the remaining coal slag in the furnace chamber and sighed in disappointment.
Using coal to smelt iron was probably a patent unique to ancient China, wasn't it? A failed patent at that...
The ancient iron smelting industry had long been plagued by excessively high phosphorus content. This was likely due to poor iron ore quality, or perhaps because of cast iron technology, or both combined. Su Shi once wrote a poem titled *Song of Coal*, highly praising the benefits of using coal to smelt iron. He believed that using coal to "smelt iron to forge weapons yields a sharpness surpassing the ordinary." It could also save charcoal and raise the furnace temperature. Indeed, coal possessed these two advantages, and it lowered the cost of iron smelting as well, being much cheaper than charcoal.
However, the deadliest assassin of iron smelting—sulfur—lurked within the coal.
Winters in the north were very cold, so the cold-shortness phenomenon of high-phosphorus ironware was extremely severe, severely restricting the development of iron implements.
Therefore, using coal to smelt iron was a complete and utter mistake that led the entire iron smelting industry astray!
Actually, the method to solve the excessively high sulfur content was very simple: making coke and using coke to smelt iron.
But the ancients didn't know how to make coke.
Fang Jun thought about it again: how was coke made? Well, he didn't know either...
However, he knew that coke was just coal burned vigorously in a sealed environment. Cement was also made by burning, glass was made by burning, and porcelain was still made by burning...
No wonder people often said that the use of "fire" was the hallmark of civilization. So that was why...
Although he didn't know the exact way to burn it, he just had to burn it. By burning it relentlessly and trying all sorts of variations, he would eventually manage to make it.
Helpless, Fang Jun once again lamented the truth of the saying: "Master physics and chemistry, and you won't be afraid no matter where you time-travel."
Coming to the blacksmith shop this day was not to inspect the iron smelting furnace, but rather to check on the task he had assigned to Lu Cheng at the Fang residence a few days prior. However, since he had now thought of coke, he naturally had to give Lu Cheng some instructions. When he had free time, Lu Cheng should experiment according to his ideas; it certainly wouldn't do any harm.
Lu Cheng, however, was completely baffled. First burn the coal, and then use the leftovers from the burned coal to smelt the ore... Wasn't this like taking off one's pants to fart—an unnecessary extra step?
Lu Cheng wore a bewildered expression, completely unable to comprehend...
Fang Jun had no way to explain further. Was he supposed to explain concepts like carbon elements, CO2, and chemical reactions to this "illiterate" man from over a thousand years ago?
In front of the row of adobe houses was a courtyard. Coal slag and slag from the ore had been crushed into fine little pieces and laid out in a thick layer, making the ground firm and even, fearless of rain or snow, and preventing it from easily becoming muddy, uneven, or potholed.
At this moment, a carriage stood right in the center of the courtyard. It was merely a crude frame without any decorative side panels or curtains.
Fang Jun walked over, pinched his chin, circled the carriage once, and felt a sense of emotion in his heart.
That's right, what he wanted to create was a four-wheeled carriage.
It was hard to imagine that the magnificent five-thousand-year civilization of China, which had invented countless world-leading technologies, had never produced a four-wheeled carriage.
It seemed incredible and hard to believe, but the fact was just that.
China had always used two-wheeled carts and had never seen four-wheeled carriages shuttling through the streets like those in Europe. In reality, four-wheeled carriages completely crushed two-wheeled carts in terms of load capacity and comfort; even the Queen of England traveled in a four-wheeled royal carriage. So what on earth was the reason that China always stuck to two-wheeled carts and never developed four-wheeled carriages?
Some people searched for various objective reasons—terrain factors, warfare factors, equine factors... But Fang Jun believed there was only one fundamental reason: the Chinese people had never solved the steering problem for four-wheeled vehicles.
Four-wheeled vehicles had appeared in China before, but such vehicles simply mounted four wheels onto a fixed frame and thus could not steer. Although such four-wheeled carriages looked like they had four wheels, they possessed no practical value whatsoever. Even if they had forty wheels, it would be useless...
If a modern person looked at this, would it even be considered a problem?
Obviously not.
The carriage before his eyes had the front two wheels mounted on one frame and the back two wheels mounted on another frame, with the rear frame mounted atop the front frame and connected by a vertical pivot axis. This perfectly solved the steering problem of a four-wheeled vehicle.
Yet many inventions were just like that—much like a layer of window paper. Once you poked through it, it was just a thin sheet; if you didn't poke through it, you could see nothing at all.
In fact, many of the simplest mechanical technologies were invented by Westerners, such as screws, bolts, nuts, gears, racks, springs, bearings, windmills, water pumps, and so on. These seemingly insignificant little things played crucial roles across the entire field of industrial production and manufacturing...
As soon as Fang Jun appeared, the few craftsmen who had been gathered around the carriage immediately scattered. Among them, a white-haired old man greeted Fang Jun with an expression of intense excitement: "Second Young Master, this creation is truly a gift from the heavens!"
Fang Jun was somewhat taken aback. Surely not?
Exaggeratedly speaking, it was just a carriage after all. There was no fundamental difference between two wheels and four wheels; he only wanted to make it because he coveted a more comfortable ride, as those two-wheeled carts were truly far too bumpy...
Lu Cheng introduced him to Fang Jun, saying, "This is the blacksmith with the best craftsmanship in our shop. He doesn't have a formal name, so everyone calls him Wang Erxiao..."
Fang Jun broke out in a sweat...
That Wang Erxiao was clearly the leader of this group of craftsmen. Only he dared to speak to Fang Jun, while all the others stood far away.
Wang Erxiao was extremely emotional, looking at Fang Jun with an expression of utter adoration as he said, "This old servant followed the Master all the way from Shandong, watching the Master step by step achieve his current success and glory. Back then, I even watched you being born, Second Young Master..."
Fang Jun broke out in a sweat once more. My father actually let you watch that...